收藏本站
PTB48560A, PTB48560B
PTB48560C
SLTS236A – MARCH 2005 – REVISED OCTOBER 2005
www.ti.com
Input Current Limiting
The converter is not internally fused. For safety and overall system protection, the maximum input current to
the converter must be limited. Active or passive current limiting can be used. Passive current limiting can be a
fast-acting fuse. A 125-V fuse, rated no more than 5 A, is recommended. Active current limiting can be
implemented with a current limited Hot-Swap controller.
Thermal Considerations
Airflow may be necessary to ensure that the module can supply the desired load current in environments with
elevated ambient temperatures. The required airflow rate is determined from the safe operating area (SOA). The
SOA is the area beneath the applicable airflow rate curve on the graph of temperature derating vs output current.
(See the Typical Characteristics.) Operating the converter within the SOA limits ensures that all the internal
components are at or below their stated maximum operating temperatures.
Using the On/Off Enable Controls on the PTB48560x Auto-Track Compatible DC/DC Converters
The converter incorporates two output enable controls. PEN (pin 2) is the positive enable input, and NEN (pin 3)
is the negative enable input. Both inputs are electrically referenced to -V I (pin 4) on the primary or input side of
the converter. The enable pins are ideally controlled with an open-collector (or open-drain) discrete transistor.
Each input has an internal pullup resistor to a reference. There is no benefit to adding pullup resistors external to
the module. If they are added, the maximum input voltage for these inputs must be limited to a maximum of 60 V.
Automatic (UVLO) Power Up
Connecting NEN (pin 3) to -V I (pin 4) and leaving PEN (pin 2) open-circuit, configures the converter for automatic
power up. The converter control circuitry incorporates an undervoltage lockout (UVLO) function, which disables
the converter until the minimum specified input voltage is present at ±V I (see the Electrical Characteristics table).
The UVLO circuitry ensures a clean transition during power up and power down, allowing the converter to
tolerate a slow rising input voltage. For most applications, the PEN and NEN enable controls can be configured
for automatic power up.
Positive Output Enable (Negative Inhibit)
To configure the converter for a positive enable function, connect NEN (pin 3) to -V I (pin 4), and apply the system
On/Off control signal to PEN (pin 2). In this configuration, applying less than 0.8 V (with respect to -V I potential)
to pin 2 disables the converter output. Figure 15 gives an example circuit that uses a MOSFET transistor.
+V I
1
2
+V I
PEN
DC/DC
Module
1 = Outputs Off
? V I
Q1
BSS138
3
4
NEN
? V I
Figure 15. Positive Enable Configuration
Negative Output Enable (Positive Inhibit)
To configure the converter for a negative enable function, PEN (pin 2) is left open circuit, and the system On/Off
control signal is applied to NEN (pin 3). A low-level control signal (less than 0.8 V) must then be applied to pin 3
to enable an output from the converter. An example of this configuration is detailed in Figure 16 .
14
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
PTH03000WAD MODULE PIP 3.3VIN 6A ADJ T/H
PTKM10-180SM TOROIDAL POWER CHOKE 10UH SMD
PV37W504C01B00 TRIMMER 500K OHM 0.25W TH
PVC6282 CAP FILM 8200PF 600VDC RADIAL
PVF2A504A11R00 TRIMMER 500K OHM 0.001W SMD
PVM-16V121MG70E-R2 CAP ALUM 120UF 16V 20% SMD
PWR1317AC CONV DC/DC +/-15V +/-50MA DIP
PWR1726AC CONV DC/DC 1.5W UNREG DIP
相关代理商/技术参数
PTB48560BAS 功能描述:DC/DC转换器 30-W 1.8V to 3.6V Adj DC/DC Converter RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
PTB48560BAZ 功能描述:DC/DC转换器 30-W 1.8V to 3.6V Adj DC/DC Converter RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
PTB48560C 制造商:TI 制造商全称:Texas Instruments 功能描述:30-W, 48-V INPUT DC/DC CONVERTERS WITH AUTO-TRACK TM SEQUENCING
PTB48560CAH 功能描述:DC/DC转换器 30-W 9V to 13.2V Adj DC/DC Converter RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
PTB48560CAS 功能描述:DC/DC转换器 30-W 9V to 13.2V Adj DC/DC Converter RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
PTB48560CAZ 功能描述:DC/DC转换器 30-W 9V to 13.2V Adj DC/DC Converter RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
PTB48580A 制造商:TI 制造商全称:Texas Instruments 功能描述:Dual Complementary-Output DC/DC Converter for DSL
PTB48580AAH 功能描述:DC/DC转换器 .+/-5V 30W Comp Out put DC/DC Converter RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: